|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Multimedia ICs Video signal switcher BA7604N The BA7604N is a switching IC developed for use in VCRs. It has two-channel analog multiplexers, and features wide dynamic range, and wide operating frequency range, and is suitable for switching audio and video signals. *Applications VCRs and TVs *Features / 1-output switches. 1) Two 2-input 2) 5V power supply. 3) Low power consumption (42mW Typ.). 4) Excellent frequency characteristics (10MHz, 0dB, Typ.). 5) Wide dynamic range (3.0VP-P Typ.). 6) High input impedance (20k Typ.). 7) Fast switching speed (50ns Typ.). *Absolute maximum ratings (Ta = 25C) Parameter Power supply voltage Power dissipation Operating temperature Storage temperature Symbol VCC Pd Topr Tstg Limits 9 500 - 40 ~ + 85 - 55 ~ + 125 Unit V mW C C Reduced by 5.0mW for each increase in Ta of 1C over 25C. *Block diagram Sa Sb 1 IN1a 2 VCC 3 IN2a 4 CTLa 5 OUTa 6 OUTb 7 CTLb 8 IN2b 9 GND 10 IN1b CTL L H Output IN2 IN1 Sa, Sb: Non-clamped 1 Multimedia ICs BA7604N *Equivalent circuits Sa, Sb IN VCC R3 13.6k I2 0.3mA Q5 R7 100 Q9 R12 200 R16 200 R4 200 R2 2.2k Q4 R6 20k R9 200 Q7 Q8 Q10 Q11 R15 200 Q3 R10 100 Q2 Q12 Q1 OUT R1 1k R5 33k I1 0.6mA R17 12k I4 0.6mA I5 1mA R11 100 R13 100 R14 100 CTL VCC R1 50k I2 0.6mA Q1 Q6 R6 25k R2 200 CTL Q3 Q5 Q2 Q4 R5 25k I1 0.25mA R3 400 R4 400 I3 0.06mA 2 Multimedia ICs BA7604N *Electrical characteristics (unless otherwise noted, Ta = 25C and VCC = 5.0V) Parameter Operating voltage Supply current Maximum output level Voltage gain Interchannel crosstalk Frequency characteristic Total-harmonic distortion CTL pin switch level Input impedance Symbol VCC ICC Vom GV CT Gf THD VTH ZIN Min. 4.5 -- 2.7 - 0.5 -- -3 -- 2.0 14 Typ. 5.0 8.4 3.0 0 - 65 0 0.007 2.5 20 Max. 5.5 13.0 -- 0.5 -- 1 -- 3.0 26 Unit V mA VP-P dB dB dB % V k Conditions -- -- f = 1kHz, THD = 0.5% f = 1MHz, VIN = 1VP-P f = 4.43MHz, VIN = 1VP-P 10MHz / 1MHz, VIN = 1VP-P f = 1MHz, VIN = 1VP-P -- -- Note: Refer to the measurement circuit given in Fig. 1. *Reference data(reference values) Pin DC voltages Pin No. 1 2 3 4 5 DC voltage 2.48 5.00 2.48 4.91 1.76 Pin No. 6 7 8 9 10 Units: Vdc DC voltage 1.76 4.91 2.48 0 2.48 Electrical characteristics Parameter Input impedance (no clamp) Output impedance Min. -- -- Typ. 20k 30 Max. -- -- Unit The input coupling capacitor values should be 0.1F to 1F. 3 Multimedia ICs BA7604N *Measurement circuit 1 2 3 4 5 6 7 8 9 10 VCC A1 223 47 V V S1a S2a S3a S3b S2b S1b 1 2 105 3 105 1 2 105 3 105 1 2 3 1 2 3 1 2 105 3 105 1 2 105 3 105 R VIN1a OSC R VIN2a OSC R VIN2b VCC VCC OSC R VIN1b OSC R = 75 4 Multimedia ICs BA7604N *Measurement conditions Parameter Current dissipation Maximum output level Voltage gain IN1a IN2a IN1b IN2b IN1a IN2a IN1b IN2b IN1a IN2a IN1b IN2b IN1a IN2a IN1b IN2b CTLa CTLb IN1a IN2a IN1b IN2b IN1a IN2a IN1b IN2b Symbol ICC Vom Vom Vom Vom GV GV GV GV CT CT CT CT Gf Gf Gf Gf VTH VTH THD THD THD THD ZIN ZIN ZIN ZIN Switch settings S1a 2 3 2 2 2 3 2 2 2 2 3 2 2 3 2 2 2 3 2 3 2 2 2 1 2 2 2 S2a 2 2 3 2 2 2 3 2 2 3 2 2 2 2 3 2 2 2 2 2 3 2 2 2 1 2 2 S3a 2 2 3 2 2 2 3 2 2 2 3 2 2 2 3 2 2 1 2 2 3 2 2 2 3 2 2 S1b 2 2 2 3 2 2 2 3 2 2 2 2 3 2 2 3 2 2 3 2 2 3 2 2 2 1 2 S2b 2 2 2 2 3 2 2 2 3 2 2 3 2 2 2 2 3 2 2 2 2 2 3 2 2 2 1 S3b 2 2 2 2 3 2 2 2 3 2 2 2 3 2 2 2 3 2 1 2 2 2 3 2 2 2 3 Measurement method Ammeter Note 1 Note 2 Interchannel crosstalk Note 3 Frequency characteristic CTL pin switching level Totalharmonic distortion Input impedance Note 4 Note 5 Note 6 Note 7 Note 1: Connect a distortion meter to the output, and input a f = 1kHz sine wave. Adjust the output level until the output distortion is 0.5%. This output voltage at this time is the maximum output level Vom (VP-P). Note 2: Input a 1VP-P, 1MHz sine wave. The voltage gain is given by GV = 20 log (VOUT / VIN). Note 3: Input a 1VP-P, 4.43MHz sine wave. The interchannel crosstalk is given by CT = 20 log (VOUT / VIN). Note 4: Input 1VP-P, 1MHz and 10MHz sine waves. The frequency characteristic is given by Gf = 20 log (VOUT (f = 10MHz) / VOUT (f = 1MHz)). Note 5: Input a 1VP-P, 1MHz sine wave. Reduce the CTL pin voltage from VCC. The CTL pin switching level (VTH) is the CTL pin voltage at which the VOUT level drops below 20mVP-P. Note 6: Input a 1VP-P, 1kHz sine wave and measure the total-harmonic distortion of the output using a total-harmonic distortion meter. Note 7: Measure the input pin voltage VIN50 when a current of DC50A is flowing into the input pin. Measure the input pin open-circuit voltage. The input impedance is given by Z = (VIN50 - VIN0) / 50 x 10-6[]. 5 Multimedia ICs BA7604N *External dimensions (Units: mm) 25.2 0.2 2.8 0.2 10.5 0.5 5.8 0.2 1.2 1 3.5 0.5 2.54 10 0.6 0.8 1.3 0.3 0.1 SIP10 6 |
Price & Availability of BA7604N |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |